RIDER INFORMATION
| Total Height |
Body
Height to Sternal Notch |
|||
| Inseam:
(Stand with your back to the wall and ‘straddle’ a 1” wide book. Measure to the top of the book.) |
Lower
Leg: L / R (seated, from top of kneecap to floor) |
|||
| Shoulder
Width: (Stand with your arms extended measure to the ‘notches’, not the muscles) |
Forearm:
L / R (from tip of elbow to knobby bone on wrist) |
|||
Circle one on each line
| Flexibility | 1 (None) | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 (Yogi) |
| Lower Back Pain | 1 (None) | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 (Ouch) |
| Upper
Back / Shoulder Pain |
1 (None) | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 (Ouch) |
| Neck Pain | 1 (None) | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 (Ouch) |
CURRENT BIKE
| Make | Model | ||
| Size | Top Tube | ||
| Seat Tube (length, angle) |
Stem | ||
| Back of
Saddle to Handlebar |
Handlebar Drop / Lift |
My Current Bike is: (Circle one on each line)
| Steering | 1 (Slow) |
2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 (Scary) |
| Rigidity | 1 (Mush) | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 (Stiff) |
| Ride Comfort | 1 (Nasty) | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 (Nice) |
| Reach | 1 (Short) | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 (Long) |
My New High Ti Bike Needs To Be: (Circle one on each line)
| Steering | 1 (Slow) |
2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 (Fast) |
| Rigidity | 1 (Plush) | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 (Aggro) |
| Ride Comfort | 1 (Plush) | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 (Aggro) |
| Reach | 1 (Short) | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 (Long) |
HIGH TI CYCLES, INC
TERMS AND CONDITIONS
Your signature of approval below indicates that you understand and agree to the following Terms and Conditions.
All information is true and correct.
Once High Ti Cycles receives your signed approval, you assume full responsibility for the specification to which you have agreed and you may not refuse delivery.
High Ti Cycles guarantees the accuracy of your frame to 1.5 mm for all lenghts and 0.3 degrees for all angles.
The ship date is an estimate. Due to the nature of custom building, lead times may vary.
Fabrication takes approximately 4 weeks after approval. Custom component assembly takes an additional week.
A non-refundable deposit of $1,000.00 is required before any drawings will be completed for your approval.
Signature ____________________________________________________________________Print Name __________________________________________________________________
Date________________________________________________________________________